-
PAGE 1
Operator's Manual Twin Rear Bagger - Model No. 19A70005OEM WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA FORM NO.
-
PAGE 2
1 To The Owner Thank You Thank you for purchasing a bagging attachment manufactured by MTD LLC. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain this attachment. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
-
PAGE 3
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! DANGER! This attachment was built to be used according to the safe operation practices in this manual.
-
PAGE 4
3. Use slow speed. Choose a low enough speed setting so that you will not have to stop or shift while on the slope. Tires may lose traction on slopes even though the brakes are functioning properly. Always keep machine in gear when going down slopes to take advantage of engine braking action. 4. Follow the manufacturer's recommendations for wheel weights or counterweights to improve stability. 5. Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.
-
PAGE 5
(r e p r e s e nts a 1 0 ° s l ope) or a fence post or a corner of a building... e lon g d o t t e d lin Fold a Sight and hold this level with a vertical tree... 10° Use this page as a guide to determine slopes where you may safely operate your mower with a grass bag attachment installed. WARNING! Do not operate your lawn mower with a bagger attachment on inclines with a slope in excess of 10 degrees (a rise of approximately 1-3⁄4 feet every 10 feet).
-
PAGE 6
3 Contents of Carton Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Fig. 3-1. Three hardware packs are included in this kit and are detailed on the following page. • Upper Chute Support • Hitch Bracket Kit (3 Pcs.
-
PAGE 7
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with three loose hardware packs enclosed and one set of hardware included in the mounting bracket kit. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis.
-
PAGE 8
4 Assembly & Installation NOTE: References to left, right, front and rear of the tractor are from the operator's position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. • For convenience, pivot the seat forward and leave it in that position until the grass collector is fully mounted and assembled.
-
PAGE 9
Mount Assembly on Tractor 3. Install mounting assembly on tractor as follows: 1. Install the bagger hanger assembly onto the mounting assembly on the tractor by hooking it over the hitch plate between the two tabs. See Fig. 4-6. Slide the mounting bracket assembly along the frame rails of the tractor until the hooks in the mounting brackets align under the shoulder bolts on your tractor, as seen in Fig. 4-4. Tabs Top View Figure 4-6 4.
-
PAGE 10
Installing the Weight Bar Assembling Remaining Bagger Components Install the weight bar onto the front of the tractor's foot rest using two 710-3022 hex screws and 712-04065 hex flange lock nuts from Hardware Pack 689-00095. Now that the mounting brackets are assembled and are in place on the tractor, follow these steps to assemble the remaining bagger components. Because the openings between the foot rest and the tractor frame (Refer to Fig.
-
PAGE 11
Make sure screen sits under the cover's lip 5. Figure 4-13 Figure 4-11 Install the bagger cover onto the bag support assembly, as seen in Fig. 4-12. The plastic cover goes inside of the two mounting tabs. Figure 4-14 7. Figure 4-12 6. Open Hood by pushing in on the rear, right-side tab with your right hand, as seen in 1 of Fig. 4-15, and lifting the cover with your left hand in the center rear of the bagger cover, 2. Slide the hinge pin into the hole located on the mounting tab, as in Fig. 4-13.
-
PAGE 12
8. Install both bag assemblies onto the bag support brackets by inserting the front edge in first, as seen in 1 of Fig. 4-16, and setting the back edge down until it fits into the assembly (2). 1 2 11. Figure 4-16 9. Install the rubber chute strap (723-04008A) on the chute elbow using a clevis pin (711-05063), flat washer (736-0204) and Bow-tie cotter pin (714-04040) found in hardware pack 689-00091. See Fig. 4-17.
-
PAGE 13
Figure 4-20 12. Secure the chute elbow to the tractor's deck by hooking the chute strap onto the ball pin installed earlier on the deck. See Fig. 4-21. 14. Figure 4-22 With the bagger cover open, install the upper chute over the chute adapter, and rest the top so that the chute support sits in the upper chute groove. See Fig. 4-23. Note: Make sure to align the upper chute with the ridges on the bagger support bracket. Figure 4-21 13.
-
PAGE 14
Operation Bagger Usage NOTE: When both grass bags are full, place the tractor on a firm, level surface, disengage the PTO, turn the tractor engine off and set the parking brake. 14 1. Lift up the grass bag cover as instructed on Page 11 in Step 7. Do not remove the chute tube assembly from the tractor. 2. Remove the grass bags by lifting these up and moving the bags away from the bag support assembly. 3.
-
PAGE 15
Notes 6 15
-
PAGE 16
19A70005OEM Parts List 2 16 15 12 6 25 4 8 15 7 13 9 11 12 5 3 10 24 6 12 20 21 29 17 23 14 1 18 28 27 22 19 16
-
PAGE 17
Ref. Part Number Description 1. 631-04295 Upper Chute Assembly 2. 631-04292 Twin Bagger Cover Assembly 3. 731-06497 Upper Chute Support 4. 731-06504 Bagger Cover Screen 5. 710-0276 Carriage Screw, 5/16-18 x 1.00" 6. 710-3008 Hex Head Screw, 5/16-18 x .75" 7. 711-0332 Clevis Pin, .50" Dia. 8. 664-04096 Grass-bag Assembly 9. 683-04481 Twin Bag Support Assembly 10. 683-04519 Vertical Support Bracket 11. 711-04988 Cover Hinge Pin 12. 712-04063 Flange Lock Nut, 5/16-18 13.
-
PAGE 18
Notes 18
-
PAGE 19
-
PAGE 20
MANUFACTURER'S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/ or its territories and possessions (either entity respectively, "MTD").
0 Response to "How to Install Bagger on Troy Bilt Push Mower"
Post a Comment